Gi.Gi. - The Best Sealer for Microcement

Gi.Gi. - The Best Sealer for Microcement

£170.00

Gi.Gi. Sealer is a polyurethane sealer for microcement and cementitious overlays such as Ercole® and Microbond®. It comes in matte. It is colourless and doesn’t turn yellow. It is extremely durable and long-lasting. It has no VOC content and has very low odour.
It can be used in areas handling forklift traffic. It is 100% UV stable. Gi.Gi. Sealer is anti-graffiti and is highly resistant to aggressive contaminants. Gi.Gi. Sealer is two-component and easy to apply.

2 in stock (can be backordered)

Ecobeton

Description

Gi.Gi sealer for microcement

Gi.Gi. Sealer is a polyurethane sealer for microcement such as Ercole® and Microbond®. It comes in matte. It is colourless and doesn't turn yellow. It is extremely durable and long-lasting. It has no VOC content and has a very low odour.
It can be used in areas handling forklift traffic. It is 100% UV stable. Gi.Gi. Sealer is anti-graffiti and is highly resistant to aggressive contaminants. Gi.Gi. Sealer is two-component and easy to apply.

Properties of Gi.Gi sealer for microcement

• Matte or satin polyurethane finish
• Can be applied by airless device or by short-haired roller (T-bar)
• It is solvent-free
• Resistant to heavy traffic
• 100% UV Stable
• Anti-scratch
• It hinders oil absorption
• Low VOC content

First primer then sealer for microcement - this is how we seal microcement
First primer then sealer - this is how we seal microcement

Uses for Gi.Gi. sealer

Gi.Gi. Sealer for microcement is supplied in the two-component kit (part A and part B) and it is used as a sealer on cementitious overlays
• Interior and exterior applications
• Residential and public places
• Vehicular surfaces
• Wet rooms, shower tall, countertop
Cementitious surfaces (floors, walls, furniture)
• Protect pool cementitious coatings

Application

Before the application of sealer, make sure the surface is free from dirt, oils, previous sealers, etc.

Surface preparation:


The surface must be perfectly hardened, structurally sound, dry and previously treated with Gi.Gi. Sealer. Before applying the first coat be sure that the surface is clean and free from dirt, oils, previous sealers. Verify the surface porosity by pouring a bit of water on it, if the water is stagnant, sanding is needed.

Mixing:


Stir the bottles before use. In a clean bucket, mix carefully Part A with Part B. Fill the bottle of Part A with clean and cold water three times and add it to the compound. Mix carefully with a mixing drill. Let the product stand for a few minutes, then pour it into the spray or pump machine. Pot life is 45 to 90 minutes, it may vary depending on the environmental conditions (temperature and moisture). We recommend preparing one kit
a time and applying the first coat.

Application:


Gi.Gi. Sealer
can be applied by spray and spread with T-bar or microfiber short nap roller. Wait until the first coat is completely dry before applying the second coat (ca. 45-180
min.). Do not over-apply. It must be applied in thin coats.
Two coats are usually sufficient, but the applicator must determine the specific need.

Sealer should be applied between 10° and 30° degrees.

Further coats typically take 3 to 8 hours to dry depending on temperature and airflow. After application, tools may be cleaned using soap and water. Light traffic is possible after 16- 24 hours and heavy traffic is possible after 24-48 hours. The sealer will gain strength over the next few days after application and will reach full cure after 7-10 days. Avoid subjecting the sealer to freezing temperatures or moisture for 12-36 hours after application.

Additional information

Weight 3 kg
Dimensions 10 × 20 × 25 cm

Brand

Ecobeton

Italian manufacturer of concrete additives, concrete repair systems and concrete protection. Also microcements and cementitious overlays
Ecobeton

Leave a Reply

Your email address will not be published. Required fields are marked *